⚡ Find the Best Battery, Solar Kit, E-Bike or Generator  ·  Capacity, output and cost per watt-hour, side by side

Home › Articles

Generac Generator Cost: Unit, Installation and Total Price

A 22 kW Generac Guardian generator typically runs $11,000 to $15,000 fully installed with the unit at Generac’s October 2026 list price, and the unit itself is roughly 40 to 55 percent of that total.

11 min readUpdated

A Generac whole-house generator costs $3,649 to $6,989 for the unit alone on the air-cooled Guardian line (maker list price, October 2026), and roughly $8,800 to $20,700 total once you add the automatic transfer switch, electrical work, gas line, concrete pad, permits and labor at the typical installer ranges below. Liquid-cooled Protector Series units for larger homes push the unit price itself past $17,000 before installation even starts. Where you land in that range depends mostly on kW size and how far the generator sits from your gas meter and electrical panel.

Generac generator cost by kW size

Generac’s residential lineup splits into two families. The Guardian Series is air-cooled and covers 10 kW to 26 kW, enough for most single-family homes running a well pump, refrigerator, furnace blower and some lighting and outlets on generator power. The Protector Series is liquid-cooled and starts around 25 kW, running up to 80 kW for very large homes or light commercial use. Generac’s own list prices for the unit only, checked on each model’s page on October 12, 2026, with output shown on propane and on natural gas:

Electricians wearing safety gear work on power lines in Nakhon Ratchasima, Thailand.
Photo: Thampapon Otavorn / Pexels
SeriesSize (model)Output, propane / natural gasCoolingUnit price (maker list price, October 2026)
Guardian10 kW (7171)10 kW / 9 kWAir-cooled$3,649
Guardian14 kW (7223)14 kW / 14 kWAir-cooled$4,569
Guardian18 kW (7226)18 kW / 17 kWAir-cooled$5,379
Guardian22 kW (7042)22 kW / 21 kWAir-cooled$6,119
Guardian22 kW with 200 A whole-house switch (7043)22 kW / 19.5 kWAir-cooled$6,979
Guardian24 kW (7209)24 kW / 21 kWAir-cooled$6,559
Guardian26 kW (7290)26 kW / 22.5 kWAir-cooled$6,989
XG Protector25 kW (XG02525AUAX)25 kW / 25 kWLiquid-cooled$17,199
XG Protector48 kW (XG04845ANAX)48 kWLiquid-cooled$25,179
XG Protector80 kW (XG08045ANAX)80 kWLiquid-cooled$33,999

The 22 kW Guardian is a common choice because it covers a typical 2,000 to 3,000 square foot home’s essentials without the load-management gear smaller units need. Generac sells the 22 kW several ways, among them the 7042 as the generator alone at $6,119 and the 7043 bundled with a 200-amp whole-house transfer switch at $6,979, so two quotes for “the 22 kW” can differ by $860 before any labor. The kW in the name is the propane rating; on natural gas Generac rates the 7042 at 21 kW and the 7043 at 19.5 kW, so size on the fuel the house actually has. Generac’s figures are MSRP, a suggested price, and dealer quotes vary, so ask for the generator as its own line on the quote.

What drives total installed cost

At list price the unit is roughly a third to a half of the total bill. The rest is site work, and every home differs on how much of it is needed:

Cost itemTypical range
Generator unit (10–26 kW Guardian, maker list price)$3,649–$6,989
Automatic transfer switch, installed$1,800–$5,500
Concrete or composite pad$300–$1,200
Electrical work (panel tie-in, wiring, load management)$1,500–$3,000
Gas line installation or extension$500–$1,500
Permits$80–$500
Installer labor beyond the above$1,000–$2,000
Typical total, installed$8,800–$20,700

Add the low end of every line and the total is about $8,830; add the high end and it is about $20,690. For a 22 kW Guardian at its $6,119 list price plus the low end of each remaining line, the total is about $11,300, and the moderate site in the worked example below comes to about $14,670, so $11,000–$15,000 is the realistic range for that size. Distance drives most of the spread: a gas line trenched 40 feet from the meter, or a panel that needs a full upgrade before the transfer switch goes in, adds thousands that a straightforward install never sees.

Size the transfer switch to the panel, not just to the generator. A 200-amp transfer switch is rated for 200A x 240V = 48,000W, but its continuous load limit is 80 percent of that rating, or 38,400W, which is one reason installers rarely spec anything smaller for a whole-house switch even on a 22 kW generator that only produces about 22,000W. A load-management module lets a smaller generator run a bigger panel safely by cycling high-draw circuits like a central air conditioner or an EV charger, and it typically adds $300–$800 to the electrical line item rather than requiring a larger, pricier generator.

Permits, inspections and the pad

Most jurisdictions require an electrical permit and a mechanical or gas permit for a standby generator, plus an inspection before it can be switched over; budget $80–$500 total and expect the installer to pull them as part of the job. The pad location also has to meet Generac’s published clearances, below, before it is poured. A standard poured concrete pad for a 10–26 kW Guardian runs $300–$600; composite pads cost more but skip the concrete cure time and let installers finish in a single visit.

Where the pad can go

Generac’s clearance guidance for its home standby generators, based on NFPA 37, sets these minimums:

ClearanceMinimum distance
From operable windows, doors, vents, window wells and other wall openings5 ft
Above the unit5 ft
Front and both ends, including trees, shrubs and bushes3 ft
Back of the unit to a wall, models with the SwRI logo only18 in
Models without the SwRI logo5 ft from combustible materials, 3 ft from non-combustible

Local code takes precedence over these figures, and Generac says not to install the unit under a wooden deck or platform. It also warns that a unit placed at the NFPA distances can still let carbon monoxide into the house, so it may need to sit farther away; CPSC advises battery-operated or battery-backup CO alarms on every level of the home and outside sleeping areas. The pad location in turn sets the length of the gas line and the wire run to the panel, which drive most of the cost spread above.

Annual maintenance cost

Generac’s owner’s manual for its 9 kW to 22 kW air-cooled generators sets this service schedule:

IntervalWhat the manual lists
After the first 25 hours of runningChange oil and oil filter; check and adjust valve clearance
Daily while running continuously, or before each useCheck oil level, check for fuel or oil leaks, check the enclosure louvers for debris
Every yearCheck the battery; check for water intrusion from sprinklers, downspouts or sump discharge
Every 2 years or 200 hoursChange oil and oil filter; check the battery
Every 4 years or 400 hoursThe 2-year items plus a new air filter, new spark plugs and a valve clearance check

Oil and filter move to every year or 100 hours in cold weather (below 40°F), or when the unit runs continuously in heat above 85°F. Generac recommends having the work done by an Independent Authorized Service Dealer, and the air filter and spark plugs have to be serviced on schedule to keep the emissions warranty valid.

A single visit from an independent installer runs $170–$450; Generac dealer maintenance plans bundling two visits a year with priority emergency scheduling run $200–$600 a year. On the manual’s schedule that is about five oil services over 10 years in a mild climate ($850–$2,250) or ten in a cold one ($1,700–$4,500), against $2,000–$6,000 on a dealer plan. Fuel burned during outages is extra and is covered below. See our generator maintenance guide for what each visit covers and how to space them on propane versus natural gas.

A worked example

A homeowner installing a 22 kW Guardian with a new 200-amp transfer switch, a 20-foot gas line run, a poured pad and a straightforward panel tie-in might see: unit $6,119 (maker list price, October 2026), transfer switch installed $3,000, pad $450, electrical $2,250, gas line $1,000, permits $350, remaining labor $1,500, for a total near $14,670. That sits near the top of the $11,000–$15,000 range for that size: shorter gas runs, simpler panels and a lower dealer price on the unit bring it closer to $11,000. Add a $350-a-year maintenance plan and the 10-year cost of ownership lands around $18,200, plus fuel burned during outages.

Fuel use and running cost in an outage

Generac publishes fuel burn for each model. The 22 kW 7042 burns 2.53 gallons of propane an hour at half load and 3.71 at full load, or 221 and 327 cubic feet of natural gas. The daily costs below use EIA’s U.S. average residential propane price of $2.598 a gallon for the week of October 5, 2026 (before taxes), and its residential natural gas prices of $13.96 per thousand cubic feet (Mcf) in January 2026 and $14.95 in February 2026.

Generator and fuelHalf loadFull load24 hours at half load
10 kW (7171), propane0.97 gal/h1.48 gal/h23 gal, about $60
10 kW (7171), natural gas101 cu ft/h127 cu ft/h2.4 Mcf, about $34–$36
22 kW (7042), propane2.53 gal/h3.71 gal/h61 gal, about $158
22 kW (7042), natural gas221 cu ft/h327 cu ft/h5.3 Mcf, about $74–$79

At full load the 22 kW burns about 89 gallons of propane a day, roughly $231, or 7.8 Mcf of natural gas, roughly $110–$117. Your own utility rate or propane contract will differ, so swap in the price from your bill.

On propane the tank caps the runtime. Every 100 gallons in the tank runs the 22 kW about 40 hours at half load, or 27 hours at full load. Generac’s minimum tank for a home standby generator is 250 gallons, and it notes a larger one may be needed depending on fuel demand and climate; ask the propane supplier how many gallons a full fill of your tank holds and divide by the hourly burn above. A natural gas unit has no tank to refill.

The battery backup alternative

A standby generator burns natural gas or propane and needs the site work above; a home battery or large power station needs no gas line and no pad, gets wired to the panel by an electrician, and produces no exhaust, which is why it can sit in a garage or basement a Generac never can. The closest battery rivals to a 22 kW Generac are wired-in home systems. Generac’s own PWRcell 2 holds 9 to 18 kWh per cabinet in 3 kWh modules, up to 36 kWh with two cabinets, and delivers up to 11.5 kW continuous with two cabinets and at least seven modules, or 5.2 to 10.5 kW from one cabinet. Its motor-starting capacity runs from 65 to 130 LRA (locked-rotor amps) depending on module count. The Tesla Powerwall 3 stores 13.5 kWh, puts out 11.5 kW continuous and starts loads rated up to 185 LRA, and up to four units can be combined. Check LRA against the air conditioner or well pump the battery has to start. At 11.5 kW, either one delivers about half the 22 kW generator’s propane rating, and a 13.5 kWh Powerwall 3 would last a little over an hour at the 11 kW half load used in the fuel table above. The two can also work together: Generac’s PWRcell 2 spec sheet lists compatibility with its single-phase air-cooled standby generators up to 28 kW with a compatible controller, with backup then limited by fuel supply rather than battery size. For plug-in and portable whole-home units, see our home battery backup guide. The UL 9540-certified EcoFlow DELTA Pro Ultra pairs a 7,200 W inverter with a 6 kWh (6,144 Wh) battery for $5,799 (maker list price, October 2026) and is built to stack extra batteries as budget allows. Smaller whole-home units like Jackery HomePower 3600 Plus (3,584 Wh) and Mango Power E (3,533 Wh) cover a refrigerator, some lighting and internet gear through a multi-hour outage but not a well pump and central air together for days the way a whole-house generator can. The honest trade-off: a generator refuels indefinitely and covers the whole house; a battery is capped by its capacity but needs no fuel and no annual service call. It is not permit-free, though: a home battery or power station connected to the panel, through a transfer switch or an inlet and interlock, normally needs an electrical permit and inspection, just as a generator does. Requirements vary with the code your state or town has adopted, and the panel wiring is a job for a licensed electrician. Only plug-in use, running appliances from the unit’s own outlets on extension cords, needs no permit. Our whole-house battery cost breakdown and power station vs. generator comparison walk through which one fits a given outage pattern, and our power station sizing guide covers matching capacity to actual circuits.

Never run a Generac or any fuel-burning generator indoors, in a garage, or near an air intake or window; it produces carbon monoxide that can be fatal within minutes. Panel connections and transfer switch wiring should always be done by a licensed electrician, and back-feeding a panel through a dryer outlet without a transfer switch is illegal in most jurisdictions and can kill utility line workers.

Frequently asked questions

How much does a 22 kW Generac generator cost installed?

Typically $11,000–$15,000 fully installed, with the unit itself at $6,119 for the 7042, or $6,979 for the 7043 with a 200-amp whole-house switch (maker list price, October 2026), and the rest going to the transfer switch, electrical work, gas line, pad, permits and labor. Simpler sites land near the bottom; long gas or wire runs push it higher.

Does the transfer switch cost come with the generator?

Sometimes. Generac sells several sizes with a matching transfer switch as one model, such as the 22 kW 7043 with a 200-amp whole-house switch; the standalone 7042 does not include one. Either way, physically installing the switch, typically $1,800–$5,500 fully installed, is a separate line item.

How much does Generac maintenance cost per year?

A single service visit runs $170–$450. Generac’s manual schedules an oil and filter change every two years or 200 hours, or every year or 100 hours in cold weather (below 40°F), so paying per visit comes to about $850–$4,500 over 10 years. A dealer plan with two visits a year and priority scheduling runs $200–$600 a year, or $2,000–$6,000 over 10 years.

Is a home battery cheaper than a Generac generator?

The equipment can cost less, but capacity is capped. A single large power station or home battery can cost less than a Generac install and needs no gas line or pad (a connection to the panel still normally needs an electrical permit and inspection), but it runs out of stored energy in hours unless paired with solar, while a fueled generator keeps running as long as gas or propane keeps arriving.

Can I install a Generac generator myself to save money?

The pad can be a do-it-yourself job, but the gas line and the electrical panel connection need a licensed gas fitter and a licensed electrician in nearly every jurisdiction, both for code compliance and because a miswired transfer switch can back-feed the utility grid and endanger line workers.

The Watt Guide
Scroll to Top